Minimum Speed 30 Preformed Thermoplastic Road Marking

  • Product code: 15355-BLUW-750
  • Start Traffic
  • Dispatches in 1-3 Days
£74.63 excl. VAT
£89.56inc. VAT
Buy in bulk and save
  • 5 or more £72.39 excl. VAT
  • 5 or more £86.87 inc. VAT
  • 10 or more £70.15 excl. VAT
  • 10 or more £84.18 inc. VAT
Symbol Size: 750mm
Specification Size guide

  • If you’re looking to order large quantities, call us on (0)1905 794875 for more information.

  • This product is made to order and, therefore, has a restricted returns policy.


You may also need the following:


Minimum Speed 30 Preformed Thermoplastic Road Marking

The ‘Minimum Speed 30’ preformed thermoplastic road marking is used to reduce the chances of stationary traffic by setting a minimum speed limit to improve traffic flow.

Commonly used in tunnels, at airports, train stations, dual carriageways and built-up areas where high levels of traffic is a common occurrence. This marking could also be used in combination with a ‘No Waiting’ road marking to show there needs to be traffic flowing through designated areas.

To help keep traffic moving, combine this marking with the post mounted sign version to add another layer of enforcement to the areas you’ll be using it in. Post mounted road signs can be found in our signage section here.

Key Features:

  • Easy Application - No special knowledge, talent or years at art school required, just a clean surface and a gas burner. Just place the marking bead side up and apply heat till fully melted onto the surface.
  • Professional Appearance - These markings always look good due to their pre-cut design.
  • Fast To Install - Minimal surface preparation is required for these markings, with a worst-case scenario requiring an application of primer.
  • Non-Slip - No need to apply glass bead to these markings as it comes embedded in them.
  • Conforms - BSEN 1871
Thermoplastic Marking being Installed

Choose From An Array Of Sizes

When travelling towards a road marking roundel at speed it needs to be intentionally distorted. This ensures that it can still be interpreted correctly by approaching motorists.

Our range of roundel sizes includes;

  • 750mm x 750mm
  • 1200mm x 1200mm
  • 2500mm x 1500mm
  • 4300mm x 1500mm

Other sizes are available upon request but may carry a longer delivery time.

Size comparison Chart

Application Of Our Minimum Speed Limit Road Marking

Applying our minimum speed limit marking is very easy. Firstly the area must be cleaned of all loose debris, oil, grease and salts. Once this is done you are ready to get going. If your road surface is old tarmac, concrete or block paving then you will need to use our fast-drying primer.

Once you have fully prepped the surface the roundel can be set out. Once you are happy with the marking positioning a heat gun can be used to melt the marking to the road surface. For additional traction glass bead can be sprinkled over the surface, this is fused into the marking with the further application of heat.

Thermoplastic On Block Paving

Thermoplastic on block paving is known to be more difficult to apply and has a substantially shorter lifetime than on bituminous surfaces, such as tarmac.

Block paving is not a solid structure. Most of the time, they are put down and sand is added into the grooves, so over time when moisture creeps in as well as moss, movement can be made within 2 blocks, making the material crack and fail.

Need Assistance?

Can't find the road marking you are looking for? Call us now on 01905 794 875 We are here to help, our trained staff are available throughout the day to take your calls or answer your messages. They will ensure that you get the best marking at the best price. Our phone lines are open during normal office hours.


Minimum Speed 30 Preformed Thermoplastic Road Marking
£74.63 excl. VAT
£89.56inc. VAT
Information

Key Facts and Information About This Product

Customers Also Viewed These Products: